Поделиться через

Wait-Event

Модуль:
Microsoft.PowerShell.Utility Module

Waits until a particular event is raised before continuing to run.

Синтаксис

Default (по умолчанию) 

Wait-Event
    [[-SourceIdentifier] <String>]
    [-Timeout <Int32>]
    [<CommonParameters>]

Описание

The Wait-Event cmdlet suspends execution of a script or function until a particular event is raised. Execution resumes when the event is detected. To cancel the wait, press CTRL+C.

This feature provides an alternative to polling for an event. It also allows you to determine the response to an event in two different ways:

  • using the Action parameter of the event subscription
  • waiting for an event to return and then respond with an action

Примеры

Example 1: Wait for the next event

This example waits for the next event that is raised.

Wait-Event

Example 2: Wait for an event with a specified source identifier

This example waits for the next event that is raised and that has a source identifier of ProcessStarted.

Wait-Event -SourceIdentifier "ProcessStarted"

Example 3: Wait for a timer elapsed event

This example uses the Wait-Event cmdlet to wait for a timer event on a timer that is set for 2000 milliseconds.

$Timer = New-Object Timers.Timer
$objectEventArgs = @{
    InputObject = $Timer
    EventName = 'Elapsed'
    SourceIdentifier = 'Timer.Elapsed'
}
Register-ObjectEvent @objectEventArgs
$Timer.Interval = 2000
$Timer.AutoReset = $false
$Timer.Enabled = $true
Wait-Event Timer.Elapsed

ComputerName     :
RunspaceId       : bb560b14-ff43-48d4-b801-5adc31bbc6fb
EventIdentifier  : 1
Sender           : System.Timers.Timer
SourceEventArgs  : System.Timers.ElapsedEventArgs
SourceArgs       : {System.Timers.Timer, System.Timers.ElapsedEventArgs}
SourceIdentifier : Timer.Elapsed
TimeGenerated    : 4/23/2020 2:30:37 PM
MessageData      :

Example 4: Wait for an event after a specified timeout

This example waits up to 90 seconds for the next event that is raised and that has a source identifier of ProcessStarted. If the specified time expires, the wait ends.

Wait-Event -SourceIdentifier "ProcessStarted" -Timeout 90

Параметры

-SourceIdentifier

Specifies the source identifier that this cmdlet waits for events. By default, Wait-Event waits for any event.

Свойства параметра

Тип:String
Default value:None
Поддерживаются подстановочные знаки:False
DontShow:False

Наборы параметров

(All)
Position:0
Обязательно:False
Значение из конвейера:False
Значение из конвейера по имени свойства:True
Значение из оставшихся аргументов:False

-Timeout

Specifies the maximum time, in seconds, that Wait-Event waits for the event to occur. The default, -1, waits indefinitely. The timing starts when you submit the Wait-Event command.

If the specified time is exceeded, the wait ends and the command prompt returns, even if the event has not been raised. No error message is displayed.

Свойства параметра

Тип:Int32
Default value:-1
Поддерживаются подстановочные знаки:False
DontShow:False
Aliases:TimeoutSec

Наборы параметров

(All)
Position:Named
Обязательно:False
Значение из конвейера:False
Значение из конвейера по имени свойства:False
Значение из оставшихся аргументов:False

CommonParameters

This cmdlet supports the common parameters: -Debug, -ErrorAction, -ErrorVariable, -InformationAction, -InformationVariable, -OutBuffer, -OutVariable, -PipelineVariable, -ProgressAction, -Verbose, -WarningAction, and -WarningVariable. For more information, see about_CommonParameters.

Входные данные

String

Выходные данные

PSEventArgs

Примечания

Events, event subscriptions, and the event queue exist only in the current session. If you close the current session, the event queue is discarded and the event subscription is canceled.