How to: Specify the Network Adapter to Use on a Test Controller or Test Agent with Multiple Network Adapters

If a computer that has the test controller or the test agent software installed has multiple network adapters then you must specify the IP address instead of the name of the computer to identify that test controller or test agent.

Binding a Test Controller to a Specific Network Adapter

To obtain the IP addresses of the network adapters

1. From Microsoft Windows, click Start, click in the Start Search box, type cmd, and then press ENTER.

2. Type ipconfig /all.

   The IP addresses for your network adapters are displayed. Record the IP address of the network adapter that you want to bind your controller to.

To Bind a Network Adapter to a Test Controller

1. From Microsoft Windows, click Start, click in the Start Search box, type services.msc, and then press ENTER.

   The Services dialog box is displayed.

2. In the results pane, under the Name column, right-click the Visual Studio Test Controller service and then click Stop.

   -or-

   Open an elevated command prompt and run the following command at a command:

   net stop vsttcontroller

3. Open the QTCcontroller.exe.config XML configuration file located in <drive letter:>\Program Files (x86)\Microsoft Visual Studio 10.0\Common7\IDE\.

4. locate <appSettings> tag.

     <appSettings>
       <add key="LogSizeLimitInMegs" value="20"/>
       <add key="AgentConnectionTimeoutInSeconds" value="120"/>
       <add key="AgentSyncTimeoutInSeconds" value="300"/>
       <add key="ControllerServicePort" value="6901"/>
       <add key="ControllerUsersGroup" value="TeamTestControllerUsers"/>
       <add key="ControllerAdminsGroup" value="TeamTestControllerAdmins"/>
       <add key="CreateTraceListener" value="no"/>
     </appSettings>
   

5. Add the BindTo key to specify which network adapter to use in the <appSettings> section.

       <add key="BindTo" value="<YOUR IP ADDRESS>"/>
     </appSettings>
   

6. Start the test controller service. To do this, run the following command at a command prompt:

   net start vsttcontroller.

   Warning

   You must run the test agent installation again to connect the test agent to the controller. This time, specify the IP address for the controller instead of the controller name.

   This applies to the controller, the agent service, and the agent process. The BindTo property must be set for each process that is running on a computer that has more than one network adapter. The procedure to set the BindTo property is the same for all three processes, as specified earlier in this topic for the test controller.

Binding a Test Agent to a Specific Network Adapter

To Bind a Network Interface Card to a Test Agent

1. From Microsoft Windows, click Start, click in the Start Search box, type services.msc, and then press ENTER.

   The Services dialog box is displayed.

2. In the results pane, under the Name column, right-click the Visual Studio Test Agent service and then click Stop.

   -or-

   Open an elevated command prompt and run the following command at a command:

   net stop vsttagent

3. Open the QTAgentService.exe.config XML configuration file located in <drive letter:>\Program Files (x86)\Microsoft Visual Studio 10.0\Common7\IDE\.

4. locate <appSettings> tag.

     <appSettings>
       <appSettings>
       <add key="LogSizeLimitInMegs" value="20"/>
       <add key="AgentServicePort" value="6910"/>
       <add key="ControllerConnectionPeriodInSeconds" value="30"/>
       <add key="StopTestRunCallTimeoutInSeconds" value="120"/>
       <add key="CreateTraceListener" value="no"/>
       <add key="GetCollectorDataTimeout" value="300"/>
     </appSettings>  </appSettings>
   

5. Add the BindTo key to specify which network adapter to use in the <appSettings> section.

       <add key="BindTo" value="<YOUR IP ADDRESS>"/>
     </appSettings>
   

6. Start the test agent service. To do this, run the following command at a command prompt:

   net start vsttagent.

See Also

Tasks

How to: Specify the Maximum Size for the Log File

How to: Specify Timeout Periods for Test Controllers and Test Agents

Concepts

Installing and Configuring Visual Studio Agents and Test and Build Controllers

Configuring a Test Controller and Test Agent Across a Firewall

Other Resources

Modifying Load Test Logging Settings