Set-EdgeSyncServiceConfig

The ConfigurationSyncInterval parameter specifies how frequently the Microsoft Exchange EdgeSync service synchronizes configuration data. The default value is 3 minutes.

To specify a value, enter it as a time span: dd.hh:mm:ss where dd = days, hh = hours, mm = minutes, and ss = seconds.

The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.

• Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax: -Confirm:$false.
• Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.

The CookieValidDuration parameter specifies how long a cookie record is valid. The default value is 21 days.

To specify a value, enter it as a time span: dd.hh:mm:ss where dd = days, hh = hours, mm = minutes, and ss = seconds.

The DomainController parameter specifies the domain controller that's used by this cmdlet to read data from or write data to Active Directory. You identify the domain controller by its fully qualified domain name (FQDN). For example, dc01.contoso.com.

The FailoverDCInterval parameter specifies how long EdgeSync waits before failing over to another domain controller if it can't read configuration data from Active Directory. The default value is 5 minutes.

To specify a value, enter it as a time span: dd.hh:mm:ss where dd = days, hh = hours, mm = minutes, and ss = seconds.

The Identity parameter specifies the name of the Microsoft Exchange EdgeSync service you want to configure.

The LockDuration parameter specifies how long an instance of the Microsoft Exchange EdgeSync service can maintain an exclusive lock on the synchronization rights. While an EdgeSync service maintains an exclusive lock on synchronization rights, no other EdgeSync service can take over synchronization. The default value is 6 minutes.

To specify a value, enter it as a time span: dd.hh:mm:ss where dd = days, hh = hours, mm = minutes, and ss = seconds.

The LockRenewalDuration parameter specifies how long before the expiry of an exclusive lock an EdgeSync service can renew the lock. The default value is 4 minutes.

To specify a value, enter it as a time span: dd.hh:mm:ss where dd = days, hh = hours, mm = minutes, and ss = seconds.

The LogEnabled parameter specifies enables or disables the EdgeSyncLog. Valid input for this parameter is $true or $false. The default value is $true.

The LogLevel parameter specifies the EdgeSync logging level. Valid values are:

• None (This is the default value)
• Low
• Medium
• High

The LogMaxAge parameter specifies the maximum duration in days to keep the EdgeSyncLog files. Log files older than the specified value can be overwritten. The default value is 30 days.

To specify a value, enter it as a time span: dd.hh:mm:ss where dd = days, hh = hours, mm = minutes, and ss = seconds.

The LogMaxDirectorySize specifies the maximum amount of disk space the EdgeSyncLog directory can use. The default value is 250 MB.

When you enter a value, qualify the value with one of the following units:

• B (bytes)
• KB (kilobytes)
• MB (megabytes)
• GB (gigabytes)
• TB (terabytes)

Unqualified values are typically treated as bytes, but small values may be rounded up to the nearest kilobyte.

The value of the LogMaxFileSize parameter must be less than or equal to the value of the LogMaxDirectorySize parameter. The valid input range for either parameter is from 1 through 9223372036854775807 bytes. If you enter a value of unlimited, no size limit is imposed on the EdgeSyncLog directory.

The LogMaxFileSize parameter specifies the maximum log file size for the EdgeSyncLog files. The default value is 10 MB.

When you enter a value, qualify the value with one of the following units:

• B (bytes)
• KB (kilobytes)
• MB (megabytes)
• GB (gigabytes)
• TB (terabytes)

Unqualified values are typically treated as bytes, but small values may be rounded up to the nearest kilobyte.

The value of the LogMaxFileSize parameter must be less than or equal to the value of the LogMaxDirectorySize parameter. The valid input range for either parameter is from 1 through 9223372036854775807 bytes. If you enter a value of unlimited, no size limit is imposed on the EdgeSyncLog files.

The LogPath parameter specifies the disk location to store the EdgeSyncLog files. The default value is TransportRoles\Logs\EdgeSync\.

The Name parameter specifies a unique name for the EdgeSync service configuration.

The OptionDuration parameter specifies how long an instance of the Microsoft Exchange EdgeSync service can maintain an optional lock on the synchronization rights. While an EdgeSync service maintains an optional lock on synchronization rights, another EdgeSync service can take over synchronization after the optional lock has expired if it's initiated using the Start-EdgeSynchronization command. The default value is 30 minutes.

To specify a value, enter it as a time span: dd.hh:mm:ss where dd = days, hh = hours, mm = minutes, and ss = seconds.

The RecipientSyncInterval parameter specifies how frequently the Microsoft Exchange EdgeSync service synchronizes recipient data from the global catalog. The default value is 5 minutes.

To specify a value, enter it as a time span: dd.hh:mm:ss where dd = days, hh = hours, mm = minutes, and ss = seconds.

The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.