Set-AutodiscoverVirtualDirectory

The BasicAuthentication parameter specifies whether Basic authentication is enabled on the virtual directory. Valid values are:

• $true: Basic authentication is enabled. This is the default value.
• $false: Basic authentication is disabled.

The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.

• Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax: -Confirm:$false.
• Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.

The DigestAuthentication parameter specifies whether Digest authentication is enabled on the virtual directory. Valid values are:

• $true: Digest authentication is enabled.
• $false: Digest authentication is disabled. This is the default value.

The DomainController parameter specifies the domain controller that's used by this cmdlet to read data from or write data to Active Directory. You identify the domain controller by its fully qualified domain name (FQDN). For example, dc01.contoso.com.

The ExtendedProtectionFlags parameter specifies custom settings for Extended Protection for Authentication on the virtual directory. Valid values are:

• None: This is the default setting.
• AllowDotlessSPN: Required if you want to use Service Principal Name (SPN) values that don't contain FQDNs (for example, HTTP/ContosoMail instead of HTTP/mail.contoso.com). You specify SPNs with the ExtendedProtectionSPNList parameter. This setting makes Extended Protection for Authentication less secure because dotless certificates aren't unique, so it isn't possible to ensure that the client-to-proxy connection was established over a secure channel.
• NoServiceNameCheck: The SPN list isn't checked to validate a channel binding token. This setting makes Extended Protection for Authentication less secure. We generally don't recommend this setting.
• Proxy: A proxy server is responsible for terminating the SSL channel. To use this setting, you need to register an SPN by using the ExtendedProtectionSPNList parameter.
• ProxyCoHosting: HTTP and HTTPS traffic may be accessing the virtual directory, and a proxy server is located between at least some of the clients and the Client Access services on the Exchange server.

The ExtendedProtectionSPNList parameter specifies a list of valid Service Principal Names (SPNs) if you're using Extended Protection for Authentication on the virtual directory. Valid values are:

• $null: This is the default value.
• Single SPN or comma delimited list of valid SPNs: The SPN value format is Protocol\FQDN. For example, HTTP/mail.contoso.com. To add an SPN that's not an FQDN (for example, HTTP/ContosoMail), you also need to use the AllowDotlessSPN value for the ExtendedProtectionFlags parameter.

The ExtendedProtectionTokenChecking parameter defines how you want to use Extended Protection for Authentication on the virtual directory. Extended Protection for Authentication isn't enabled by default. Valid values are:

• None: Extended Protection for Authentication isn't be used on the virtual directory. This is the default value.
• Allow: Extended Protection for Authentication is used for connections between clients and the virtual directory if both the client and server support it. Connections that don't support Extended Protection for Authentication will work, but may not be as secure as connections that use Extended Protection for Authentication.
• Require: Extended Protection for Authentication is used for all connections between clients and the virtual directory. If either the client or server doesn't support it, the connection will fail. If you use this value, you also need to set an SPN value for the ExtendedProtectionSPNList parameter.

Note: If you use the value Allow or Require, and you have a proxy server between the client and the Client Access services on the Mailbox server that's configured to terminate the client-to-proxy SSL channel, you also need to configure one or more Service Principal Names (SPNs) by using the ExtendedProtectionSPNList parameter.

This parameter is available only in Exchange Server 2010.

The ExternalUrl parameter specifies the URL used to connect to the virtual directory from outside the network firewall.

The Identity parameter specifies the Autodiscover virtual directory that you want to modify. You can use any value that uniquely identifies the virtual directory. For example:

• Name or Server\Name
• Distinguished name (DN)
• GUID

The Name value uses the syntax "VirtualDirectoryName (WebsiteName)" from the properties of the virtual directory. You can specify the wildcard character (*) instead of the default website by using the syntax VirtualDirectoryName*.

This parameter is available only in Exchange Server 2010.

The InternalUrl parameter specifies the URL used to connect to the virtual directory from inside the network firewall.

The OAuthAuthentication parameter specifies whether OAuth authentication is enabled on the virtual directory. Valid values are:

• $true: OAuth authentication is enabled. This is the default value.
• $false: OAuth authentication is disabled.

The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.

The WindowsAuthentication parameter specifies whether Integrated Windows authentication is enabled on the virtual directory. Valid values are:

• $true: Integrated Windows authentication is enabled. This is the default value.
• $false: Integrated Windows authentication is disabled.

The WSSecurityAuthentication parameter specifies whether WS-Security (Web Services Security) authentication is enabled on the virtual directory. Valid values are:

• $true: WS-Security authentication is enabled. This is the default value.
• $false: WS-Security authentication is disabled.