New-SweepRule

The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.

• Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax: -Confirm:$false.
• Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.

The DestinationFolder parameter specifies an action for the Sweep rule that moves messages to the specified folder. The syntax is MailboxID:\ParentFolder[\SubFolder].

For the value of MailboxID, you can use any value that uniquely identifies the mailbox. For example:

• Name
• Alias
• Distinguished name (DN)
• Canonical DN
• Domain\Username
• Email address
• GUID
• LegacyExchangeDN
• SamAccountName
• User ID or user principal name (UPN)

Example values for this parameter are [email protected]:\Unimportant or John:\Inbox\Misc. The default value is MailboxID:\Deleted Items.

This parameter is available only in on-premises Exchange.

The DomainController parameter specifies the domain controller that's used by this cmdlet to read data from or write data to Active Directory. You identify the domain controller by its fully qualified domain name (FQDN). For example, dc01.contoso.com.

The Enabled parameter specifies whether the Sweep rule is enabled or disabled. Valid values are:

• $true: The rule is enabled. This is the default value.
• $false: The rule is disabled.

After you create the rule, you can enable or disable it by using the Enable-SweepRule and Disable-SweepRule cmdlets.

This parameter is available only in on-premises Exchange.

The ExceptIfFlagged parameter specifies an exception for the Sweep rule that looks messages with a message flag applied. Valid values are:

• $true: The rule action isn't applied to messages that have a message flag applied.
• $false: The exception isn't used.

The typical message flag values are:

• Any
• Call
• DoNotForward
• FollowUp
• ForYourInformation
• Forward
• NoResponseNecessary
• Read
• Reply
• ReplyToAll
• Review

This parameter is available only in on-premises Exchange.

The PinMessage parameter specifies an exception for the Sweep rule that looks for pinned messages. Valid values are:

• $true: The rule action isn't applied to messages that are pinned to the top of the Inbox.
• $false: The exception isn't used.

The KeepForDays parameter specifies an action for the Sweep rule that specifies the number of days to keep messages that match the conditions of the rule. After the number of days have passed, the messages are moved to the location that's specified by the DestinationFolder parameter (by default, the Deleted Items folder).

You can't use this parameter with the KeepLatest parameter and the Sweep rule must contain a KeepForDays or KeepLatest parameter value.

The KeepLatest parameter specifies an action for the Sweep rule that specifies the number of messages to keep that match the conditions of the rule. After the number of messages is exceeded, the oldest messages are moved to the location that's specified by the DestinationFolder parameter (by default, the Deleted Items folder).

You can't use this parameter with the KeepForDays parameter and the Sweep rule must contain a KeepForDays or KeepLatest parameter value.

The Mailbox parameter specifies the mailbox where you want to create the Sweep rule. You can use any value that uniquely identifies the mailbox. For example:

• Name
• Alias
• Distinguished name (DN)
• Canonical DN
• Domain\Username
• Email address
• GUID
• LegacyExchangeDN
• SamAccountName
• User ID or user principal name (UPN)

The Name parameter specifies the name of the Sweep rule. If the value contains spaces, enclose the value in quotation marks.

The Provider parameter specifies the provider for the Sweep rule. If the value contains spaces, enclose the value in quotation marks.

For Sweep rules that you create in Outlook on the web, the default value is Exchange16.

The Sender parameter specifies a condition for the Sweep rule that looks for the specified sender in messages. For internal senders, you can use any value that uniquely identifies the sender. For example:

• Name
• Alias
• Distinguished name (DN)
• Canonical DN
• Email address
• GUID

For external senders, use their email address.

The SourceFolder parameter specifies a condition for the Sweep rule that looks for messages in the specified folder. The syntax is MailboxID:\ParentFolder[\SubFolder].

For the value of MailboxID, you can use any value that uniquely identifies the mailbox. For example:

• Name
• Alias
• Distinguished name (DN)
• Canonical DN
• Domain\Username
• Email address
• GUID
• LegacyExchangeDN
• SamAccountName
• User ID or user principal name (UPN)

Example values for this parameter are [email protected]:\Marketing or John:\Inbox\Reports. The default value is MailboxID:\Inbox.

The SystemCategory parameter specifies a condition for the sweep rule that looks for messages with the specified system category. System categories are available to all mailboxes in the organization. Valid values are:

• NotDefined
• Bills
• Document
• DocumentPlus
• Event
• Family
• File
• Flight
• FromContact
• Important
• LiveView
• Lodging
• MailingList
• Newsletter
• Photo
• Purchase
• RentalCar
• RestaurantReservation
• RetiredPromotion
• ShippingNotification
• Shopping
• SocialUpdate
• Travel
• Video

The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.