New-MailboxRepairRequest

The Archive switch specifies whether to repair or detect corruption the archive mailbox that's associated with the specified mailbox. You don't need to specify a value with this switch.

If you don't use this switch, only the primary mailbox is included.

You can't use this switch with the Database parameter.

The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.

• Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax: -Confirm:$false.
• Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.

The CorruptionType parameter specifies the type of corruption that you want to detect and repair. You can use the following values:

• AbandonedMoveDestination*: Exchange 2016 or later, but only with the Database parameter, not the Mailbox parameter.
• AggregateCounts*: Aggregate counts on folders that aren't reflecting correct values.
• BigFunnelMissingPOIs*: Exchange 2016.
• BigFunnelPOI: Exchange 2019.
• CleanupFilesFolder*: Exchange 2016 or later.
• CleanupGraphNodesWithPropertyError*: Exchange 2016 or later.
• CleanupOfficeGraphFolders*: Exchange 2016 or later.
• CleanupOfficeGraphSsc: Exchange 2016 or later.
• CleanupOrphanedIndexes*: Exchange 2016 or later.
• CleanupTrendingAroundMe*: Exchange 2016 or later.
• CorruptJunkRule*: Exchange 2013 or later.
• CorruptSearchFolderCriteria*: Exchange 2016 or later.
• CorruptedPerUserData*: Exchange 2016 or later.
• DropAllLazyIndexes*: Exchange 2013 or later.
• EmptyFilesFolder*: Exchange 2016 or later.
• Extension1: Exchange 2013 or later, but reserved for internal Microsoft use.
• Extension2: Exchange 2013 or later, but reserved for internal Microsoft use.
• Extension3: Exchange 2013 or later, but reserved for internal Microsoft use.
• Extension4: Exchange 2013 or later, but reserved for internal Microsoft use.
• Extension5: Exchange 2013 or later, but reserved for internal Microsoft use.
• FocusedInboxCleanup*: Exchange 2016 or later.
• FolderACL*: Exchange 2013 or later.
• FolderView*: Views on folders that aren't returning correct contents.
• ImapId*: Exchange 2013 or later.
• LockedMoveTarget*: Exchange 2013 or later, but only if the mailbox is locked.
• MessageId
• MessagePtagCn
• MissingSpecialFolders: Exchange 2013 or later.
• OlcFolderCleanup: Exchange 2016 or later.
• ProvisionedFolder: Provisioned folders that are incorrectly pointing into parent folders that aren't provisioned.
• ReduceRedundantAI*: Exchange 2016 or later.
• RemovePICWFolder: Exchange 2016 or later, but reserved for internal Microsoft use.
• ReplState: Exchange 2013 or later.
• RestrictionFolder: Exchange 2013 or later.
• RuleMessageClass: Exchange 2013 or later.
• ScheduledCheck: Exchange 2013 or later.
• SearchFolder: Search folder corruption.
• SyncDefaultFolderLocalizationWithMailbox: Exchange 2016 or later.
• UniqueMidIndex: Exchange 2013 or later.

You can specify multiple values separated by commas.

* You can only use this value by itself.

The Database parameter repairs or detects corruption in all mailboxes in the specified database. You can use any value that uniquely identifies the database. For example:

• Name
• Distinguished name (DN)
• GUID

You can't use this parameter with the Mailbox parameter.

To avoid performance issues, you're limited to one active database repair request at a time.

The DetectOnly switch specifies that you want to report errors, but not fix them. You don't need to specify a value with this switch.

The DomainController parameter specifies the domain controller that's used by this cmdlet to read data from or write data to Active Directory. You identify the domain controller by its fully qualified domain name (FQDN). For example, dc01.contoso.com.

The Force switch hides warning or confirmation messages. You don't need to specify a value with this switch.

This switch runs the command immediately without waiting to be dispatched by workload management.

The Mailbox parameter specifies the mailbox that you want to repair or detect corruption in. You can use any value that uniquely identifies the mailbox. For example:

• Name
• Alias
• Distinguished name (DN)
• Canonical DN
• Domain\Username
• Email address
• GUID
• LegacyExchangeDN
• SamAccountName
• User ID or user principal name (UPN)

You can't use this parameter with the Database parameter.

The StoreMailbox parameter specifies the mailbox GUID of the mailbox you want to repair or detect corruption in. Use this parameter with the Database parameter.

Run the Get-MailboxStatistics cmdlet to find the mailbox GUID for a mailbox.

The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.