Compare-TextMessagingVerificationCode

Reference

Module:: ExchangePowerShell

Applies to:: Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019, Exchange Online

This cmdlet is available in on-premises Exchange and in the cloud-based service. Some parameters and settings may be exclusive to one environment or the other.

Use the Compare-TextMessagingVerificationCode cmdlet to verify the text messaging verification code that the user specified as part of configuring text message notifications on the mailbox.

For information about the parameter sets in the Syntax section below, see Exchange cmdlet syntax.

Syntax

Compare-TextMessagingVerificationCode
       [[-Identity] <MailboxIdParameter>]
       -VerificationCode <String>
       [-Confirm]
       [-DomainController <Fqdn>]
       [-WhatIf]
       [<CommonParameters>]

Description

The Compare-TextMessagingVerificationCode cmdlet returns the value true if the code matches the stored code that was generated by the Send-TextMessagingVerificationCode cmdlet.

When text messaging notifications are enabled on a mailbox, you can configure calendar notifications, voice mail notifications, and email notifications using an inbox rule.

You need to be assigned permissions before you can run this cmdlet. Although this topic lists all parameters for the cmdlet, you may not have access to some parameters if they're not included in the permissions assigned to you. To find the permissions required to run any cmdlet or parameter in your organization, see Find the permissions required to run any Exchange cmdlet.

Examples

Example 1

Compare-TextMessagingVerificationCode -Identity TonySmith -VerificationCode 111555

This example compares the verification code 111555 to the code sent to Tony Smith's mobile phone.

Example 2

Compare-TextMessagingVerificationCode -Identity [email protected] -VerificationCode 123456

This example compares the verification code 123456 to the code sent to Tony Smith's mobile phone.

Example 3

Compare-TextMessagingVerificationCode -Identity TonySmith -VerificationCode 111555 -Confirm $true

This example compares the verification code 111555 to the code sent to Tony Smith's mobile phone after confirmation is given.

Parameters

-Confirm

The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.

Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax: -Confirm:$false.
Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.

Type:	SwitchParameter
Aliases:	cf
Position:	Named
Default value:	None
Required:	False
Accept pipeline input:	False
Accept wildcard characters:	False
Applies to:	Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019, Exchange Online

-DomainController

This parameter is available only in on-premises Exchange.

The DomainController parameter specifies the domain controller that's used by this cmdlet to read data from or write data to Active Directory. You identify the domain controller by its fully qualified domain name (FQDN). For example, dc01.contoso.com.

Type:	Fqdn
Position:	Named
Default value:	None
Required:	False
Accept pipeline input:	False
Accept wildcard characters:	False
Applies to:	Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019

-Identity

The Identity parameter specifies the mailbox where you are trying to enable text messaging notifications. You can use any value that uniquely identifies the mailbox. For example:

Name
Alias
Distinguished name (DN)
Canonical DN
Domain\Username
Email address
GUID
LegacyExchangeDN
SamAccountName
User ID or user principal name (UPN)

Type:	MailboxIdParameter
Position:	1
Default value:	None
Required:	False
Accept pipeline input:	True
Accept wildcard characters:	False
Applies to:	Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019, Exchange Online

-VerificationCode

The VerificationCode parameter contains the verification code that the user specified.

Type:	String
Position:	Named
Default value:	None
Required:	True
Accept pipeline input:	False
Accept wildcard characters:	False
Applies to:	Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019, Exchange Online

-WhatIf

The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.

Type:	SwitchParameter
Aliases:	wi
Position:	Named
Default value:	None
Required:	False
Accept pipeline input:	False
Accept wildcard characters:	False
Applies to:	Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019, Exchange Online

Inputs

Input types

To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn't accept input data.

Outputs

Output types

To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn't return data.

Share via